MDT1283B display 12.1 inch CRT, often used in Mazak system, such as Japan Toshiba system. mdt-1283B mdt-1283-crtMDT-1283B signal identification: The implementation of the project: the original MDT-1283B six
Mitsubishi M335 System SHARP A1QA8DSP40 DisplayBelow is a picture of an old CRT monitorThis display is: Mitsubishi M335 system SHARP A1QA8 DSP40Mazak 14-inch CRT LCD Display ReplacementProduct features:MAZAK Machining Center 14-inch CRT color CRT SHARP A1QA8 DSP40, signal port 15-pin Molex interface, the actual use of 10
FANUC 15M System TX-1450, C14C-1472D1F-A DisplayBelow is a picture of an old CRT monitorA61L-0001-0094 Fanuc display (TX-1450, C14C-1472D1F-A) is the earliest Fanuc display. It is installed in Fanuc system 15, 15T, 15M, 15-A and 15-B control system. The signal interface is HONDA MR-20M. The display is a 14-inch color CRT display. It is now replaced by liquid crystal display.Plug and play, in situ installation. The effect is very good.
HAAS Monitor 28HM-NM4 HAAS Monitor Crt 28HM-NM4 LCD RetrofitHAAS CRT Monitor 28HM-NM4 is one of HAAS 12 inch CRT mono monitor displays for CNC. It was fitted on the Haas old VF1, VF2, VF3 system .HAAS Monitor Crt: KEC R12QPDB-HHaas Monitor 9 PINWe have new HAAS Monitor Crt 28HM-NM4 9pin Mono LCD Retrofit in stock , the 28HM-NM4 is used on HAAS VF1, VF2, VF3 system , its tested and setup on HAAS controls , our replacement monitors are the same D-sub 9conectors .Haas Monitor LCDHaas Monitor V2.5Haas Monitor D-sub 9
Detailed Product Description Mitsubishi C-5470NS Monitor, 14-inch color CRT monitor . This is for replace LCD monitor Technical parameters of KTV148 industrial screen:Type RGB EGA CGA MDA ScreenScreen size246*184.4mm(length*width),12.1 inches,4:3Sweep rangeH-row scanning: 15Khz ~ 48Khz Plus-n-minus auto-adaptationV-row scanning: 48hz ~ 75hz Plus-n-minus auto-adaptationInput signalSignal source typesMDA,CGA,EGA,VGARGB,RGsB,RGBS,RGBHV signalsSynchronization methodHV row filed separation, HV row field mix Cs, green segregation SogTTL digital level: 2.4 ~ 5.0V or
Detailed Product DescriptionMode:6FC4600-0AR04Panel:LCDSiemens Monitor 6FC3998-7FA20 6FC4600-0AR04Siemens-SM0901 579417TA-LCDSiemens Monitor-6FC4600-0AR04Siemens Monitor 6FC4600-0AR04 , is one of the mid generation of Siemens 12″ crt monitor display.. It was fitted on the Siemens CNC special 805 control systems (automobile industry). The 6FC4600-0AR04 is a 12″ Colour monitor.Replacement Specifications: type: LCD4600 Siemens Monitor 6FC4600-0AR04 CRT replacement,AUO industrial LCD panel,1 BNC signal connector,AC85-265V power supply ,separate OSD keys,easy to mount and
Detailed Product DescriptionCNC Monior replacement RGB,MDA,CGA,EGA to VGA ConverterFanuc Tatung Heidenhain Mazak SMT Magnetek and more!! This device is mainly used for industrial use , if you have industrial device with old Monitor , but the monitor is already broken , then what is the best way to get the industrial device to work ? replace the new system ? NO!! the industrial device cost is thousands of Dollars at least , you just need to purchase this and then connect to LCD or VGA device , the problem would be solved !! with only 2 hundred and a little more dollars Features&
Mazak CNC Mitsubishi Monitor C-5470NSLCD replacementMitsubishi Monitor C-5470NSmubishi Monitor-C-5470NSC-5470NS Mitsubishi monitor, is a relatively new generation monitor, that was fitted on the Mitsubishi Mildasand Quickturn Controls, as well as Mazatrol, Mazak, Yamazaki machine tools utilising Mitsubishi control systems. The C-5470NS is a 14 inch colour crt display.Replacement Specifications:type: LCD5470 MITSUBISHI 14″ color CRT replacement,SHARP industrial LCD panel,15 pin signal connector ,AC85-265V power supply ,separate OSD keys,easy to mount and
Detailed Product DescriptionModels:MDT962B-1A, BM09DFPower Supply:AC100-230V (50 / 60Hz)Signal Input:VIA 10 PIN EDGESize:CRT (cathode Ray Tube) 9-inch9-inch Related models: MDT962B-1A, BM09DF, MDT962B-4A, MDT947, MDT947B-1A, MDT947B-2BThe products for industrial LCD monitors for updating substitute 9-inch Mitsubishi CNC system M3 M310 M520 M500 M50 E60 M64M64S C64 used in the system (MDT962B-1A, BM09DF, MDT962B-4A, MDT947, MDT947B-1A, MDT947B-2) BM09DF single amber CRT type monitor kinescope (part corresponds Mitsubishi factory model is FCUA-CT100) OLD CRT: Mitsubishi MDT962B-1A, BM0
MDT1283B display 12.1 inch CRT, often used in Mazak system, such as Japan Toshiba system. mdt-1283B mdt-1283-crtMDT-1283B signal identification: The implementation of the project: the original MDT-1283B six
Detailed Product DescriptionSpecifications: InputSignalsMDA,CGA,EGA,RGB,RGB Sog,RGBS,RGBHV,YPbPrInterface9pin,3pin,6pin,14pin,20pin,25pinHorizontal Frequency Rate(H)12kHz to 40kHzautomatically recognized OutputSupports15pin VGA,Resolution:800*600/60HZor custom-resolutionInterfaceD-Sub 15 PIN standard VGA portPowerDC 12V 1.0A Note:1.YPbPr = YUV 2.Input Horizontal Frequency Rate 12kHz to 40kHz automatically recognized.3.Support RGB and YPbPr 4.Support Interlaced Scanning and Line by Line Scanning.5.Support Vertical Resolution from
This LCD can be compatible to replace the following FANUC System CRT:A61L-0001-0092,A61L-0001-0086,A61L-0001-0076A61l-0001-0092 and a61l-0001-0086 were produced in the middle and late 1980s. It is widely used in various FANUC systems, such as 10, 10t, 11 and 11m series displays. This 9 "monochrome CRT display was first installed on the early fanaco 10 series control system.Produced in the mid-1980s, a61l-0001-0076 is a 9-inch green monochrome display installed on FANUC 6T, 6b, 6m, 6MB, 6tb, 6mbii and 6tbii control systems.Fanuc-CRT MDT-947 A61L-0001-0086 "9"" Color CRT Monitor,
Fanuc CNC 9 inch CRT Monitor A61L-0001-00929'MONOCHROME CRT display unit for Fanuc system OA and OB series controlsFANUC 9 "CRT (A61L-0001-0092) 90 in the mid-1990s, has been widely used in various FANUC systems, such as: 0-TC, 0-MC, 16T, 18T, 16M, 18M, 21M, 21T, 0-TD, 0-MD system, A61L-0001-0093 is a 9 inch single displayamber, double frequency support, the use of more than 10 years, the majority of this type CRT display tube andhigh
Detailed Product DescriptionProduct DetailsFANUC 9 "CRT (A61L-0001-0090) produced in the mid-1990s, has been widelyused in various FANUC system, such as: 0-TC, 0-MC, 16T, 18T, 16M, 18M, 21M, 21T, 0- TD, 0-MD system display .A61L-0001-0090 is a 9-inch color display. dual frequency support, after more than 10 years of use, the majority ofA61L-0001-0090 models of CRT monitors CRT and high voltage circuit aging, not normal work is displayed.For most A61L-0001-0090
Fanuc monitor A61L-0001-0094, A61L-0001-0094#A,C14C-1472D1F-A,TX-1450AB5,A02B-0094-C041 Liquid crystal substitution FANUC A61L-0001-0094The Fanuc monitor A61L-0001-0094 replacement is in stock. have been building 0094 color CRT and now LCD / TFT replacements since 2009 for theA61L-0001-0094, A61L-0001-0094#A,/TX-1450AB5 and the A02B-0094-C041; these monitors were fitted on the following Fanuc Controls: 15A, 15B/C, 15M, 15T, 15TF, 15TT, 16-P and many other Fanuc control systems, utilising many different graphics cards. The FANUC A61L-0001-0094 LCD monitors Ver2.5 for
Detailed Product DescriptionFanuc 14 "CRT Display Model D15CM-01A, A61L-0001-0096 Display Maintenance CNC Display Maintenance ReplacementA61L-0001-0096 display is the earliest in FANUC.Commonly used in Fanuc 6 series or Fanuc 10, Fanuc 11, Fanuc 12 control system, the display is 14 inch color CRT display.Fanuc cnc D15CM-01A / A61L-0001-0096 CRT DISPLAY industrial monitors repair : A61L-0001-0096 Fanuc monitorThe signal interface is different from the conventional display of FANUC :
view {{page_size}}
Sort by :{{pop_rules}}
Sort by :Popularity
Price: Low to High
Price: High to Low
Newest First
Popularity
Categories
{{cate.name}}
{{cate.name}}