RGB MDA CGA EGA to VGA KT-809 industrial video converter

RGB, MDA, CGA,EGA to VGA Converter

(MODEL KT-809)

2010-08

KT-809 is based on the oldindustrial video converter launch of an innovative industrial Video Converter, KT-809industrial video converter of industrial fully automated operation.

Quick reference for KT-809:

KT-809Size:155MM*100*15mm

KT-809Performance and characteristic

1. MDA,CGA, EGA, RGB, RGB SOG, RGBS,RGB cs, RGBHV, YUV Signal auto scan
(Horizontal Scanning Frequency: 12K-40K, Vertical Scanning Frequency:unconstrained).

2. Vertical Resolution: 160-600 lines, autoscan.
3. Horizontal resolution: unconstrained, autoscan.
4. Supports sync separation, CS composite sync,SOG green sync, YPbPr (SOY) sync.
5. Supports monochrome, Grayscale, color signalinput.

Quick reference for KT-809 interface

DC12V: PowerSupply, DC 5-12V/1.0A.

VGA OUT: StandardVGA/SVGA,800*600/60hz

15 Pin Video in: 15 Pin D-SUB input
9 Pin Video in: 9 PinD-SUB input

MENU: Toassess OSD menu.

+、-: Toadjust the OSD menu.

V: VerticalScanning Frequency.

H/CS: HorizontalScanning Frequency, or compositesync.

R/Pr: Redsignal, or the color of the PR.

G/Y: Green signal, or chromatic aberrationof Y.

B/Pb: Bluesignal, or chromatic aberration of Pb.

LED1: PowerLED.

Note: 9 pin D-SUB,15 pin D-SUB and BNC input signal, you can choose one of them.

1. H_Position: Moves the position of the display area on the screen.

2. Width: adjust the width of the menu.

3. V_Position: Moves the position of the display area on the screenvertically.

4. Higth: Adjust the heightof the menu.

5. Phase: Adjust the phaseof the menu.

6. Style: Signal style,RGB(A) Analog, RGB(D) Digital TTL,YUV.

7. Sync: Signal Sync mode: Separate(HV), Composite(S), SOG, SOY.

Automaticrecognition of video input sync, or custom of video input sync.

8. Resistance: Inputimpedance: 75 ohm or 750 ohm.

9. Scanning: Interlacedor Progressive.

10. Exit: Save and Exit.

11. 15 seconds, don'tpress any key, the menu automatically and exit. (No signal input, the OSD menuwill display)

KT-809 Control buttons

1、 Menu: To access OSD menu.

2、 +，-：To adjust the OSD menu.

Using the Screen Adjustment Menu
(OSD: On Screen Display)

STEP 1

Connectedto signal, no display or display color is not correct, adjust the Signal style( RGB(A) Analog/RGB(D) Digital TTL/YUV).

STEP 2

KT-809can automatically identify the sync signal, if the display distortions thatneed to manually adjust the sync signal ( Separate (HV) / Composite (S)/ SOG, SOY ).

STEP 3

If the screenshows elongated, and the overflow to the bottom of the screen, choose thescanning mode adjusted: Progressive, or screen display is still only half ofthe monitor, choose the scanning mode to adjust to: interlaced.

STEP 4

Adjust thehorizontal position, horizontal size, vertical position, vertical size of theitem, adjust the monitor to display properly.

STEP 5

Input impedance: Select the correct input impedance.

STEP 6

Adjustment thephase until the display clearly.

STEP 7

Save and exit.